DIY Tub Installation.
DIY Tub Installation.
Blog Article
We've discovered this post on A Step-by-Step Guide to Installing a Bathtub down the page on the net and figured it made good sense to relate it with you on my blog.
Mounting a tub isn't exactly brain surgery, yet it does require strong plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably difficult task. If the old tub is conveniently accessible, the task can move immediately; if you have to open up a wall to get rid of the old tub as well as position the brand-new bathtub, the task is a lot harder. In either situation, the task is within a home handyman's abilities, although you will require a helper to move out the old bathtub and embeded in the new one. See to it you have certified yourself for the work and fit attempting it. As opposed to employing a contractor to take control of a halfway-completed project, it is far better to consider using one before you start. Chances are you may require an expert plumber to make tube links.
This short article will certainly aid you install a brand-new bath tub in your bathroom if you have currently bought a new tub as well as do not need to change the arrangement of your previous water system pipes.
Your tools and also material list should make up the following:
Preparing for the Setup
To start with, the supporting framework provided with the bathroom ought to be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to ensure that if the tap includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets device to prevent stress on the tub.
Fit the adaptable tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is detach the water system. After doing so, switch on the taps to drain any type of water remaining in the system. The process of removing the existing taps can be quite problematic due to the restricted access that is frequently the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a cloth all set for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have actually been eliminated, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this process. As soon as the faucets have been removed, the holes in the bath/basin will need to be cleaned up of any type of old sealing substance.
Prior to proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Mounting the Tub
Utilizing the two wood boards under its feet, put the bathtub in the called for setting. The wooden boards are helpful in equally spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four small factors.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bathtub till the spirit level reviews level.
To install faucets, fit the bottom of the outermost flexible faucet port to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Turn on the water supply as well as check all joints and also new pipework for leakages and tighten them if essential. Fill the bath tub and additionally inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub must wait till the bathtub has actually been made use of at least once as this will certainly resolve it into its final placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a link to the current supply pipelines.
If you need to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the mounting opening in the bath/basin making certain that the washers are in area in between the tap as well as the sink. Safeguard the faucet in place with the producer given backnut. Once the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal tap ports. The previous kind should be connected to the tap finishes initially, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, triggering the water to pass through the wall between the bath as well as the tiling, causing issues with wetness and also feasible leakages to the ceiling below.
You can select from a variety of coloured sealants to blend in your components and also installations. They are offered in tubes as well as cartridges, as well as are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of drenched paper or soft rope. Keep in mind to always fill the bath tub with water prior to securing, to enable the movement experienced when the bathtub remains in usage. The sealant can crack rather very early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or water-proof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was introduced to that write-up on Installing A Bathtub through an associate on our other website. Are you aware of anybody else who is very much interested in the topic? Please feel free to share it. Thanks so much for going through it.
Free Estimate Report this page